氣力輸送因工藝布置簡單、管道走向靈活、密閉式輸送、無揚塵點等特點被廣泛使用。氣力輸送根據輸送壓力和料氣比分為稀相輸送和濃相輸送，下面介紹適用于長距離的濃相倉式氣力輸送裝置工作原理和工作流程。倉式泵工作原理倉式氣力輸送裝置的功能是以壓縮氣體作為動力源對粉狀物料進行管道輸送。以壓力容器作為發生器（即倉式泵），結合差壓式發送器和推送式發送器的特點，氣體分上中下三路進入泵體內流化和輸送，由底部充氣裝置輸送物料。隨著輸送的進行，頂部氣體逐漸轉化為靜壓能壓送物料，中底部氣體起到流化物料和輸送物料的作用，并由靜壓能逐漸轉化為動壓能。物料在管道中以集團流運動為主，輸送末期形成快速的沙丘狀移動，整個輸送過程呈梯形線變化?？諝鈮嚎s機提供0.5-0.75MPa氣源。

　　Pneumatic conveying is widely used due to its simple process layout, flexible pipeline routing, closed conveying, and no dust points. Pneumatic conveying is classified into dilute phase conveying and dense phase conveying based on conveying pressure and material gas ratio. The following introduces the working principle and workflow of dense phase bin pneumatic conveying devices suitable for long-distance transportation. Working principle of warehouse pump The function of the silo type pneumatic conveying device is to use compressed gas as a power source to transport powdered materials through pipelines. Using a pressure vessel as a generator (i.e. a chamber pump), combined with the characteristics of differential pressure transmitters and push type transmitters, gas enters the pump body in three paths, upper, middle, and lower, for fluidization and transportation, and is transported by a bottom inflation device. As the transportation progresses, the top gas gradually converts into static pressure energy to transport materials, while the middle and bottom gases play a role in fluidization and conveying materials, gradually converting static pressure energy into dynamic pressure energy. The material in the pipeline mainly moves in a group flow, forming a rapid sand dune like movement at the end of transportation, and the entire transportation process changes in a trapezoidal line. The air compressor provides a 0.5-0.75MPa air source.

　　單倉泵和雙倉泵通常使用一臺獨立輸送的倉式氣力輸送裝置成為單倉泵，使用兩臺組合在一起的倉式氣力輸送裝置為雙倉泵。他們的區別在于：倉式泵為間歇式工作，在進料時不能輸送，輸送時不能進料。當工藝要求來料連續或要求輸送連續時，可以通過并聯兩臺單倉泵的方式組成雙倉泵，一臺進料時另一臺輸送，彼此交替工作，以滿足工藝要求。工作流程氣力輸送程序設有本地自動運行，手動運行和中控自動運行等方式，以單倉泵自動運行為例，當控制系統氣動運行后，氣力輸送裝置排氣閥、進料閥打開、流化閥、輸送閥關閉裝料開始，當達到設定的料位或時間時，進料閥、排氣閥自動關閉，延時5-8s，流化閥、輸送閥打開，輸送開始；當泵內壓力低于設定壓力時，控制系統發出信號，輸送閥、流化閥關閉，輸送完成。

　　Single chamber pumps and double chamber pumps typically use a single independent pneumatic conveying device to form a single chamber pump, while using two combined pneumatic conveying devices to form a double chamber pump. The difference between them is that the bin pump works intermittently and cannot transport materials during feeding. When the process requires continuous incoming materials or continuous conveying, two single chamber pumps can be connected in parallel to form a double chamber pump, with one feeding and the other conveying alternately to meet the process requirements. Workflow The pneumatic conveying program is equipped with local automatic operation, manual operation, and central control automatic operation modes. Taking the automatic operation of a single bin pump as an example, when the control system is operated pneumatically, the exhaust valve, feed valve, fluidization valve, and conveying valve of the pneumatic conveying device are opened, and the feeding valve and exhaust valve are closed to start loading. When the set material level or time is reached, the feeding valve and exhaust valve are automatically closed for a delay of 5-8 seconds, and the fluidization valve and conveying valve are opened to start conveying; When the pressure inside the pump is lower than the set pressure, the control system sends a signal, the delivery valve and fluidization valve close, and the delivery is completed.

　　泵體上安裝料位傳感器，根據工藝要求可使用性能更加穩定的稱重傳感器替代，用于指示倉滿信號。壓力傳感器用于檢測 泵內輸送壓力變化情況，當壓力高于堵管設定壓力時，自動報警，系統停止輸送；當泵內壓力達到泵空壓力時，此時輸送完成，進入下一個循環。WARM WINTER

　　 Install a level sensor on the pump body, which can be replaced with a more stable weighing sensor according to process requirements to indicate the full bin signal. Pressure sensors are used to detect changes in the conveying pressure inside the pump. When the pressure exceeds the set pressure for pipe blockage, an automatic alarm is triggered and the system stops conveying; When the pressure inside the pump reaches the pump air pressure, the delivery is completed and the next cycle begins. WARM WINTER

　　倉式泵氣力輸送原理

　　Principle of Pneumatic Conveying with Warehouse Pump

　　氣力輸送的過程就是風能轉化為物料運動的動能。氣力輸送的優化設計就是提高料氣的能量轉化率以及延遲物料動能的衰減。

　　 The process of pneumatic conveying is the conversion of wind energy into kinetic energy for material movement. The optimization design of pneumatic conveying is to improve the energy conversion rate of material gas and delay the attenuation of material kinetic energy.

　　01倉泵流態化

　　01 Warehouse pump fluidization

　　在倉式氣力輸送裝置的泵體中設有流態化裝置目的是提高能量轉換率，壓縮氣力經流態化裝置噴入泵體中，讓料氣混合后充分流態化，將風能轉化為物料的動能。流態化的時間達到一定時間后，打開出料閥，讓物料進入管道輸送，進入管道內的料氣形成穩定的集團流一起運動。

　　 The purpose of installing a fluidized bed device in the pump body of the silo pneumatic conveying device is to improve the energy conversion rate. Compressed air is sprayed into the pump body through the fluidized bed device, allowing the material gas to mix and fully fluidized, converting wind energy into kinetic energy of the material. After a certain period of fluidization time, the discharge valve is opened to allow the material to enter the pipeline for transportation. The material gas entering the pipeline forms a stable group flow and moves together.

　　03風能轉化為動能

　　03 Conversion of Wind Energy into Kinetic Energy

　　 隨著風能逐漸轉化為物料的動能，壓縮氣力的壓力逐漸變小，當管徑不變時，體積逐漸增大，風速增加而物料的速度未變，出現料氣粉?，F(xiàn)象，長時間極易造成堵塞。04變徑設計

　　As wind energy gradually converts into kinetic energy of materials, the pressure of compressed air gradually decreases. When the pipe diameter remains unchanged, the volume gradually increases, and the wind speed increases while the material velocity remains unchanged, resulting in the phenomenon of material gas particles, which can easily cause blockage over a long period of time. 04 Variable diameter design

　　為了延遲料氣分離，保持料氣呈集團狀在管道內持續穩定運動至管道出口，可對輸料管進行管徑設計。通過增加管徑的方式降低氣流速度，讓氣流速度與物料集團流的速度越接近越好，設計時通常將水平管道、彎頭和垂直管道等折算為當量距離，按照統一的管道阻力分配，再折回實際水平管道、彎頭和垂直管道。在當量輸送距離小于500米時，可不變管徑或一次變管徑；在當量距離輸送超過500m時，根據工藝可一次或多次變管徑。

　　 In order to delay the separation of material and gas and maintain the continuous and stable movement of material and gas in a group within the pipeline until the pipeline outlet, the diameter of the conveying pipe can be designed. By increasing the diameter of the pipe, the airflow velocity can be reduced to be as close as possible to the velocity of the material group flow. In design, horizontal pipes, elbows, and vertical pipes are usually converted into equivalent distances and distributed according to a unified pipeline resistance, and then folded back to the actual horizontal pipes, elbows, and vertical pipes. When the equivalent conveying distance is less than 500 meters, the pipe diameter can be kept constant or changed at once; When the equivalent distance of transportation exceeds 500m, the pipe diameter can be changed one or more times according to the process.

　　THE END 結尾隨著氣力輸送技術的進步以及加工制造業水平的提高,氣力輸送具備運行穩定、短距離輸送能耗與機械輸送相當、維護成本低等特點，氣力輸送更大的優勢在于操作簡單和密閉式管道化輸送，沒有揚塵點和污染源，符合國家環保要求，氣力輸送在化工、新能源、塑料橡膠、礦產冶金等行業應用廣泛。

　　The End With the advancement of pneumatic conveying technology and the improvement of processing and manufacturing industry level, pneumatic conveying has the characteristics of stable operation, short distance conveying energy consumption comparable to mechanical conveying, and low maintenance cost. The greater advantage of pneumatic conveying is its simple operation and closed pipeline conveying, without dust points and pollution sources, which meets national environmental protection requirements. Pneumatic conveying is widely used in industries such as chemical, new energy, plastic rubber, mineral metallurgy, etc.

　　本文由  倉泵 情奉獻.更多有關的知識請點擊  http://m.iyouth-china.com/  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is dedicated by Cang Pump For more related knowledge, please click http://m.iyouth-china.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.