倉泵（又稱倉式泵）是一種在高壓下輸送粉狀物料的氣力輸送裝置倉泵（又稱倉式泵）是一種在高壓下輸送粉狀物料的密相動壓氣力輸送裝置，廣泛應用于工業領域。以下是對倉泵的具體介紹：

　　Warehouse pump (also known as bin pump) is a pneumatic conveying device that transports powdered materials under high pressure. Warehouse pump (also known as bin pump) is a dense phase dynamic pressure pneumatic conveying device that transports powdered materials under high pressure and is widely used in the industrial field. The following is a specific introduction to the bin pump:

　　1. 工作原理

　　1. Working principle

　　進料過程：打開進料閥和排氣閥，倉式泵在常壓下進料，直到水平料位計發出倉滿指示信號為止。

　　Feeding process: Open the feeding valve and exhaust valve, and feed the silo pump under normal pressure until the horizontal level gauge sends out a full silo indicator signal.

　　加壓過程：關閉進料閥和排氣閥，然后打開高壓氣閥使罐內加壓。

　　Pressurization process: Close the feed valve and exhaust valve, then open the high-pressure air valve to pressurize the tank.

　　輸送過程：當達到操作壓力后，打開輸送空氣閥門和卸料閥，物料開始輸送。

　　Conveying process: When the operating pressure is reached, open the conveying air valve and discharge valve, and the material begins to be conveyed.

　　清吹過程：由壓力開關、料位計或時間繼電器顯示出輸送結束。此時關閉高壓氣閥和卸料閥，使全部壓縮空氣都用來清吹輸送管道；同時打開排氣閥，使罐內壓力減至常壓狀態。

　　Clear blowing process: The conveying end is displayed by a pressure switch, level gauge, or time relay. At this time, close the high-pressure air valve and discharge valve, so that all compressed air is used to blow the conveying pipeline; Simultaneously open the exhaust valve to reduce the pressure inside the tank to atmospheric pressure.

　　2. 主要特點

　　2. Main features

　　高節能：由于流化結構合理，物料流化狀態良好，耗氣量明顯比同類產品低。

　　High energy saving: Due to the reasonable fluidization structure and good material fluidization state, the gas consumption is significantly lower than similar products.

　　料氣比高：流化效果好，耗氣量少，料氣比自然就高。通過試驗室試驗，當量距離在500米以內，料氣比達到30Kg（灰）/Kg（氣）以上。

　　High material to gas ratio: good fluidization effect, low gas consumption, naturally high material to gas ratio. Through laboratory tests, the equivalent distance is within 500 meters, and the material to gas ratio reaches 30kg (ash)/Kg (gas) or more.

　　物料流速低：由于耗氣量少，料氣比高，物料在管道中呈部分流運動，實現了動靜壓輸送，因此物料輸送時流速低，設備的閥門及管路磨損量小，易損件壽命長。

　　Low material flow rate: Due to low gas consumption and high material to gas ratio, the material flows partially in the pipeline, achieving dynamic and static pressure conveying. Therefore, the material flow rate is low during transportation, and the wear of equipment valves and pipelines is small, resulting in long service life of vulnerable parts.

　　調節功能強：具有一、二次進氣調節等多種調節手段，能使系統在最佳用氣量配比及優良的流化狀態下運行。

　　Strong adjustment function: It has multiple adjustment methods such as primary and secondary air intake adjustment, which can enable the system to operate at the optimal air consumption ratio and excellent fluidization state.

　　排堵方式獨特：采用了倒抽式排堵方式，簡單易行，運行合理，只需將料氣混合物通過排堵閥及管道引至料倉或煙道入口。

　　Unique blockage removal method: Adopting a reverse suction blockage removal method, it is simple and easy to operate, and runs reasonably. Only the material gas mixture needs to be led to the silo or flue inlet through the blockage removal valve and pipeline.

　　配套設施易解決：由于耗氣量小，速度低，因此料倉料氣分離及過濾設備可以比一般倉式泵所配備的要小，造成的空氣污染也小。

　　Easy to solve supporting facilities: Due to low gas consumption and speed, the material gas separation and filtration equipment in the silo can be smaller than those equipped with general silo pumps, resulting in less air pollution.

　　能耗系數?。簜}式泵輸送系統的能耗系數在65KW.h/t.m以下。

　　Low energy consumption coefficient: The energy consumption coefficient of the silo pump conveying system is below 65KW. h/t.m.

　　自動化程度高：采用了可編程（PLC）控制系統，整個工作過程可以完全實施自動化。該系統可設定為自動、手動操作方式。主控柜安裝于系統控制室內。

　　High degree of automation: Adopting a programmable logic controller (PLC) control system, the entire work process can be fully automated. The system can be set to automatic or manual operation modes. The main control cabinet is installed in the system control room.

　　3. 技術參數

　　3. Technical parameters

　　泵體內徑：800mm至2400mm不等。

　　Pump body inner diameter: ranging from 800mm to 2400mm.

　　總?cè)莘e：0.35m?至9.25m?不等。

　　Total volume: ranging from 0.35m to 9.25m.

　　配用輸送管徑：DN50至DN175不等。

　　Suitable conveying pipe diameter: ranging from DN50 to DN175.

　　使用溫度：≤120℃。

　　Operating temperature: ≤ 120 ℃.

　　最大輸送距離：>500~1500m。

　　Maximum conveying distance:>500~1500m.

　　最大設計壓力：0.78Mpa。

　　Maximum design pressure: 0.78Mpa.

　　輸送量：3m?/h至42m?/h不等。

　　Conveying capacity: ranging from 3m?/h to 42m?/h.

　　4. 應用范圍

　　4. Scope of application

　　電廠粉煤灰輸送：倉泵可用于電廠粉煤灰的輸送，不受自然條件影響，能確保物料不受潮，環保無污染。

　　Power plant fly ash transportation: The bin pump can be used for the transportation of power plant fly ash, which is not affected by natural conditions, can ensure that the material is not affected by moisture, and is environmentally friendly and pollution-free.

　　水泥及生料輸送：適用于水泥廠的水泥及生料輸送，提高生產效率，降低能耗。

　　Cement and raw material transportation: Suitable for cement and raw material transportation in cement plants, improving production efficiency and reducing energy consumption.

　　礦粉輸送：可用于礦山行業的礦粉輸送，適應性強，能滿足不同物料的輸送需求。

　　Mineral powder transportation: It can be used for mineral powder transportation in the mining industry, with strong adaptability, and can meet the transportation needs of different materials.

　　總的來說，倉泵以其高效節能、料氣比高、物料流速低等特點，在工業領域得到了廣泛應用。無論是電廠粉煤灰、水泥生料還是礦粉等粉狀物料的輸送，倉泵都能提供穩定可靠的解決方案。對于需要處理粉狀物料的企業來說，倉泵無疑是一個值得考慮的選擇。

　　Overall, bin pumps have been widely used in the industrial field due to their high efficiency, energy saving, high material to gas ratio, and low material flow rate. Whether it is the transportation of powdered materials such as power plant fly ash, cement raw materials, or mineral powder, bin pumps can provide stable and reliable solutions. For enterprises that need to handle powdered materials, warehouse pumps are undoubtedly a worthwhile choice to consider.

　　本文由 倉泵  友情奉獻.更多有關的知識請點擊  http://m.iyouth-china.com/  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Cang Pump For more related knowledge, please click http://m.iyouth-china.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Stay tuned　　倉泵（又稱倉式泵）是一種在高壓下輸送粉狀物料的氣力輸送裝置倉泵（又稱倉式泵）是一種在高壓下輸送粉狀物料的密相動壓氣力輸送裝置，廣泛應用于工業領域。以下是對倉泵的具體介紹：

　　Warehouse pump (also known as bin pump) is a pneumatic conveying device that transports powdered materials under high pressure. Warehouse pump (also known as bin pump) is a dense phase dynamic pressure pneumatic conveying device that transports powdered materials under high pressure and is widely used in the industrial field. The following is a specific introduction to the bin pump:

　　1. 工作原理

　　1. Working principle

　　進料過程：打開進料閥和排氣閥，倉式泵在常壓下進料，直到水平料位計發出倉滿指示信號為止。

　　Feeding process: Open the feeding valve and exhaust valve, and feed the silo pump under normal pressure until the horizontal level gauge sends out a full silo indicator signal.

　　加壓過程：關閉進料閥和排氣閥，然后打開高壓氣閥使罐內加壓。

　　Pressurization process: Close the feed valve and exhaust valve, then open the high-pressure air valve to pressurize the tank.

　　輸送過程：當達到操作壓力后，打開輸送空氣閥門和卸料閥，物料開始輸送。

　　Conveying process: When the operating pressure is reached, open the conveying air valve and discharge valve, and the material begins to be conveyed.

　　清吹過程：由壓力開關、料位計或時間繼電器顯示出輸送結束。此時關閉高壓氣閥和卸料閥，使全部壓縮空氣都用來清吹輸送管道；同時打開排氣閥，使罐內壓力減至常壓狀態。

　　Clear blowing process: The conveying end is displayed by a pressure switch, level gauge, or time relay. At this time, close the high-pressure air valve and discharge valve, so that all compressed air is used to blow the conveying pipeline; Simultaneously open the exhaust valve to reduce the pressure inside the tank to atmospheric pressure.

　　2. 主要特點

　　2. Main features

　　高節能：由于流化結構合理，物料流化狀態良好，耗氣量明顯比同類產品低。

　　High energy saving: Due to the reasonable fluidization structure and good material fluidization state, the gas consumption is significantly lower than similar products.

　　料氣比高：流化效果好，耗氣量少，料氣比自然就高。通過試驗室試驗，當量距離在500米以內，料氣比達到30Kg（灰）/Kg（氣）以上。

　　High material to gas ratio: good fluidization effect, low gas consumption, naturally high material to gas ratio. Through laboratory tests, the equivalent distance is within 500 meters, and the material to gas ratio reaches 30kg (ash)/Kg (gas) or more.

　　物料流速低：由于耗氣量少，料氣比高，物料在管道中呈部分流運動，實現了動靜壓輸送，因此物料輸送時流速低，設備的閥門及管路磨損量小，易損件壽命長。

　　Low material flow rate: Due to low gas consumption and high material to gas ratio, the material flows partially in the pipeline, achieving dynamic and static pressure conveying. Therefore, the material flow rate is low during transportation, and the wear of equipment valves and pipelines is small, resulting in long service life of vulnerable parts.

　　調節功能強：具有一、二次進氣調節等多種調節手段，能使系統在最佳用氣量配比及優良的流化狀態下運行。

　　Strong adjustment function: It has multiple adjustment methods such as primary and secondary air intake adjustment, which can enable the system to operate at the optimal air consumption ratio and excellent fluidization state.

　　排堵方式獨特：采用了倒抽式排堵方式，簡單易行，運行合理，只需將料氣混合物通過排堵閥及管道引至料倉或煙道入口。

　　Unique blockage removal method: Adopting a reverse suction blockage removal method, it is simple and easy to operate, and runs reasonably. Only the material gas mixture needs to be led to the silo or flue inlet through the blockage removal valve and pipeline.

　　配套設施易解決：由于耗氣量小，速度低，因此料倉料氣分離及過濾設備可以比一般倉式泵所配備的要小，造成的空氣污染也小。

　　Easy to solve supporting facilities: Due to low gas consumption and speed, the material gas separation and filtration equipment in the silo can be smaller than those equipped with general silo pumps, resulting in less air pollution.

　　能耗系數?。簜}式泵輸送系統的能耗系數在65KW.h/t.m以下。

　　Low energy consumption coefficient: The energy consumption coefficient of the silo pump conveying system is below 65KW. h/t.m.

　　自動化程度高：采用了可編程（PLC）控制系統，整個工作過程可以完全實施自動化。該系統可設定為自動、手動操作方式。主控柜安裝于系統控制室內。

　　High degree of automation: Adopting a programmable logic controller (PLC) control system, the entire work process can be fully automated. The system can be set to automatic or manual operation modes. The main control cabinet is installed in the system control room.

　　3. 技術參數

　　3. Technical parameters

　　泵體內徑：800mm至2400mm不等。

　　Pump body inner diameter: ranging from 800mm to 2400mm.

　　總?cè)莘e：0.35m?至9.25m?不等。

　　Total volume: ranging from 0.35m to 9.25m.

　　配用輸送管徑：DN50至DN175不等。

　　Suitable conveying pipe diameter: ranging from DN50 to DN175.

　　使用溫度：≤120℃。

　　Operating temperature: ≤ 120 ℃.

　　最大輸送距離：>500~1500m。

　　Maximum conveying distance:>500~1500m.

　　最大設計壓力：0.78Mpa。

　　Maximum design pressure: 0.78Mpa.

　　輸送量：3m?/h至42m?/h不等。

　　Conveying capacity: ranging from 3m?/h to 42m?/h.

　　4. 應用范圍

　　4. Scope of application

　　電廠粉煤灰輸送：倉泵可用于電廠粉煤灰的輸送，不受自然條件影響，能確保物料不受潮，環保無污染。

　　Power plant fly ash transportation: The bin pump can be used for the transportation of power plant fly ash, which is not affected by natural conditions, can ensure that the material is not affected by moisture, and is environmentally friendly and pollution-free.

　　水泥及生料輸送：適用于水泥廠的水泥及生料輸送，提高生產效率，降低能耗。

　　Cement and raw material transportation: Suitable for cement and raw material transportation in cement plants, improving production efficiency and reducing energy consumption.

　　礦粉輸送：可用于礦山行業的礦粉輸送，適應性強，能滿足不同物料的輸送需求。

　　Mineral powder transportation: It can be used for mineral powder transportation in the mining industry, with strong adaptability, and can meet the transportation needs of different materials.

　　總的來說，倉泵以其高效節能、料氣比高、物料流速低等特點，在工業領域得到了廣泛應用。無論是電廠粉煤灰、水泥生料還是礦粉等粉狀物料的輸送，倉泵都能提供穩定可靠的解決方案。對于需要處理粉狀物料的企業來說，倉泵無疑是一個值得考慮的選擇。

　　Overall, bin pumps have been widely used in the industrial field due to their high efficiency, energy saving, high material to gas ratio, and low material flow rate. Whether it is the transportation of powdered materials such as power plant fly ash, cement raw materials, or mineral powder, bin pumps can provide stable and reliable solutions. For enterprises that need to handle powdered materials, warehouse pumps are undoubtedly a worthwhile choice to consider.

　　本文由 倉泵  友情奉獻.更多有關的知識請點擊  http://m.iyouth-china.com/  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Cang Pump For more related knowledge, please click http://m.iyouth-china.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Stay tuned